Response surface methodology toward the optimization of high-energy carotenoid extraction from Aristeus antennatus shrimp

High-energy assisted extraction techniques, like ultrasound assisted extraction (UAE) and microwave assisted extraction (MAE), are widely applied over the last years for the recovery of bioactive compounds such as carotenoids, antioxidants and phenols from foods, animals and herbal natural sources. Especially for the case of xanthophylls, the main carotenoid group of crustaceans, they can be extracted in a rapid and quantitative way with the use of UAE and MAE.     

Anti-wear beam effects on gas–solid hydrodynamics in a circulating fluidized bed

Anti-wear beams installed on water walls of circulating fluidized bed (CFB) boilers are one of the most effective ways to protect against water-wall erosion. Beam effects from, for example, beam size and superficial gas velocity were investigated on gas–solid hydrodynamics in a CFB test rig using CFD simulations and experimental methods. The downward flow of the wall layer solids is observed to be disrupted by the beam but is then restored some distance further downstream. When falling solids from the wall layer hit the anti-wear beam, the velocity of the falling solids decreases rapidly. A fraction of the solids accumulates on the beam. Below the beams, the falling solids have reduced velocities but upward-moving solids were observed on the wall. The effect of the beam increases with width and superficial gas velocity. Wear occurs mainly above the beam and its variation with width is different above to below the beam. There is an optimum width that, when combined with beam height, results in less erosion.     

Mechanism of Insertion Reactions between Silylenoid H2SiLiF and GeH3R (R =F,OH, NH2): a Theoretical Study

Theoretical investigations on the insertion reaction mechanisms of three- membered-ring silylenoid H2 Si Li F with GeH 3R(R = F, OH, NH2) have been systematically carried out by combined density functional theory(DFT) and ab initio quantum chemical calculations. The geometries of all stationary points for these reactions were optimized using the B3 LYP method and then the QCISD method was used to calculate the single-point energies. The calculated results indicate that, there are one precursor complex(Q), one transition state(TS), and one intermediate(IM) which connect the reactants and the products along the potential energy surface. The insertion reactions of three-membered-ring silylenoid with Ge H3 R proceed in a concerted manner, forming H2RSi-Ge H3 and Li F. The calculated potential energy barriers of the three reactions are 29.17, 30.90, and 54.07 k J/mol, and the reaction energies for the three reactions are –127.05, –116.91, and –103.31 k J/mol, respectively. The insertion reactions in solvents are similar to those in vacuum. Under the same situation, the insertion reactions should occur easily in the following order: GeH 3-F GeH 3-OH GeH 3-NH2. The elucidations of the mechanism of these insertion reactions provided a new mode of silicon-germanium bond formation.     

Strain effects on multiferroic BiFeO3 films

The field of multiferroics has experienced a rapid progress resulting in the discovery of many new physical phenomena. BiFeO₃ (BFO) compound, which is one of the few room-temperature single-phase multiferroics, has contributed subsequently to this progress. As a result, significant review articles have been devoted specifically to this famous system. This chapter is dedicated to the strain effects on the structure stability and property changes of BFO thin films. It is a short and non-exhaustive topical overview that may be seen as an invitation for interested readers to go beyond. There is a very active and prolific research in this field and we apologize to the authors whose relevant work is not cited here. After a short introduction, we will thus review the effect of strain on BFO films by describing the consequences on the structure and the phase transitions as well as on polar, magnetic and magnetoelectric properties.     

Above,below, and in‐between the two glass transitions of ultrathin free‐standing polystyrene films: Thermal expansion coefficient and physical aging

In previous work we observed two simultaneous transitions in high molecular weight (MW) free‐standing polystyrene films that were interpreted as two thickness‐dependent reduced glass transition temperatures (T_gs). The weaker lower transition agreed well with the MW‐dependent T_g(h) previously reported, while the much stronger upper transition matched the MW‐independent T_g(h) previously observed in low‐MW free‐standing films. Here, we investigate the nature of these two transitions by inspecting the temperature dependence of the films' thermal coefficient of expansion (TCE) and present physical aging measurements using ellipsometry both below and in‐between the two transitions. TCE values indicate approximately 80 to 90% of the film solidifies at the upper transition, while only 10 to 20% remains mobile to lower temperatures, freezing out at the lower transition. Physical aging is observed at a temperature below the upper transition, but above the lower transition, indicative of the upper transition being an actual glass transition associated with the α‐relaxation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 64–75     

Charge transport properties of MDMO PPV thin films cast in different solvents

Charge transport properties in thin films of Poly(2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylenevinylene) (MDMO PPV) cast using either chloroform (CF), toluene (TOL), or chlorobenzene (CB) as solvent were investigated. Hole mobility (μ) in these thin films measured using time‐of‐flight transient photoconductivity showed an increasing trend with respect to the solvent used in the same order, that is, μ_CF (2.4 × 10^?7 cm²/Vs) < μ_TOL (6.9 × 10^?7 cm²/Vs) < μ_CB (2.3 × 10^?6 cm²/Vs). Observed variations in mobilities were attributed to different morphologies of MDMO PPV chains in thin films cast using the aforesaid solvents. Nature of the interchain interactions and aggregate formation were obtained using photoluminescence (PL), Raman spectroscopy, and AFM studies. Ratio of PL peak intensities of 0–0 and 0–1 transitions, which is a direct measure of interchain interaction, was the highest in CB and lowest in CF. Variation in the relative intensities of out‐of‐plane wagging of vinylene group (～963 cm^?1 mode) in Raman spectra suggested different extent of coiling of polymer chains in these thin films. From these observations, it was elicited that aggregate size and interchain interactions are highest in CB and least in CF. AFM‐based topographic images of thin films further supported these variations in the size of aggregates. Variation in the aggregate sizes and interchain interactions explained the corresponding variation in the mobility. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1431–1439     

Connecting free volume with shape memory properties in noncytotoxic gamma‐irradiated polycyclooctene

The free volume holes of a shape memory polymer have been analyzed considering that the empty space between molecules is necessary for the molecular motion, and the shape memory response is based on polymer segments acting as molecular switches through variable flexibility with temperature or other stimuli. Therefore, thermomechanical analysis (TMA) and positron annihilation lifetime spectroscopy (PALS) have been applied to analyze shape recovery and free volume hole sizes in gamma‐irradiated polycyclooctene (PCO) samples, as a noncytotoxic alternative to more conventional PCO crosslinked via peroxide for future applications in medicine. Thus, a first approach relating structure, free volume holes and shape memory properties in gamma‐irradiated PCO is presented. The results suggest that free volume holes caused by gamma irradiation in PCO samples facilitate the recovery process by improving movement of polymer chains and open possibilities for the design and control of the macroscopic response. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1080–1088     

A post curing strategy toward the feasible covalent adaptable networks in polyacrylate latex films

The implementation of covalent adaptable networks (CANs) in general resin system is becoming attractive. In this work, we propose a simple post-curing strategy based on the core-shell structured acrylate latex for the achievement on both the improved general performance and the CANs characteristics in latex films. The building to the CANs was relied on the introduction of 4,4′-diaminophenyl disulfide as the curing agent, which cured the acetoacetoxy decorated shell polymer through the ketoamine reaction. The metathesis reaction of aromatic disulfides in the crosslinking segments enabled the thermally induced dynamic behavior of the network as revealed in the stress relaxation tests by comparison with other diamine crosslinking agents without the incorporation of disulfide. The synergism of the dynamic crosslinking of the shell polymer and static crosslinking in the core polymer contributed to the improved mechanical strength (15 MPa, strain% = 250%) and the suppressed water adsorption (~1% in 24 h of soaking) of the latex film, which exhibited above 90% of recovery in both strength and strain from a cut-off film damage within 1 h at 80°C. Moreover, the cured latex film could be recycled, and 75% of the mechanical performance was regained after three fragmentation-hot-pressing cycles. These, in addition with the feasible and environmental friendly characteristics, suggest a sustainable paradigm toward the smart thermosetting latex polymers.     

Precise Synthesis and Thin Film Self-Assembly of PLLA-b-PS Bottlebrush Block Copolymers

The ability of bottlebrush block copolymers (BBCPs) to self-assemble into ordered large periodic structures could greatly expand the scope of photonic and membrane technologies. In this paper, we describe a two-step synthesis of poly(l-lactide)-b-polystyrene (PLLA-b-PS) BBCPs and their rapid thin-film self-assembly. PLLA chains were grown from exo-5-norbornene-2-methanol via ring-opening polymerization (ROP) of l-lactide to produce norbornene-terminated PLLA. Norbonene-terminated PS was prepared using anionic polymerization followed by a termination reaction with exo-5-norbornene-2-carbonyl chloride. PLLA-b-PS BBCPs were prepared from these two norbornenyl macromonomers by a one-pot sequential ring opening metathesis polymerization (ROMP). PLLA-b-PS BBCPs thin-films exhibited cylindrical and lamellar morphologies depending on the relative block volume fractions, with domain sizes of 46–58 nm and periodicities of 70–102 nm. Additionally, nanoporous templates were produced by the selective etching of PLLA blocks from ordered structures. The findings described in this work provide further insight into the controlled synthesis of BBCPs leading to various possible morphologies for applications requiring large periodicities. Moreover, the rapid thin film patterning strategy demonstrated (>5 min) highlights the advantages of using PLLA-b-PS BBCP materials beyond their linear BCP analogues in terms of both dimensions achievable and reduced processing time.